38" Traditional PVC Window Boxes - No Rot
Flower Window Boxes TM brand PVC window boxes are helping to transform the window box industry as your affordable no rot solution to window boxes that look, paint, and feel identical to wood, but without the maintenance. The Traditional design is a classical look and this model has an optional base trim feature that can be added at the time of ordering to accentuate traditional flair and style, or can be left off, allowing your flowers to dominate the landscape. Decorative window box brackets can also be added which greatly enhance the look of your new boxes. All of our traditional window box planters come in standard white ready for installation or can be painted to match your home’s exterior decor.
38" Traditional PVC Window Box Features:
- Traditional style matching most classic architectural designs
- Insect-resistant and does not absorb moisture
- Will never rot and backed with a 100 percent LIFETIME GUARANTEE
- Durable construction does not warp, twist or distort in any way
- Hand crafted from high quality 5/8-inch-thick dense and solid PVC planks that won’t splinter, split or crack
- Ships fully assembled to save time on installation (not as a kit)
- Drain holes are placed at the bottom for easy drainage of excessive moisture
- Does not peel paint and can be painted with any exterior latex paint
- Available in standard or extra-large (XL) size
- Optional white decorative brackets are available. The brackets are not required but will greatly enhance the look of your boxes. If you prefer brackets in a different style than shown on the image, please specify in the special instructions at checkout.
38" Traditional PVC Window Box Measurements:
- Standard Dimensions: 8" High x 9-5/8" Wide x 38" Long
- XL Dimensions: 10" High x 10-7/8" Wide x 38" Long
- Decorative trim adds 3.25" to the total length at the top (and 1.5" at bottom if optional base trim is added).
Window box brackets are decorative only and not required, but greatly enhance the look of our window boxes. Lag bolt installation through the back of the box is recommended for easy installation. Install instructions are included or you may also check our video on how to install window boxes for more guidance. Easy and convenient self-watering reservoir system can be added and will cut your watering frequency by three-fold saving you time and making maintenance for vacations and those with busy lifestyles easy! Only available at Flower Window Boxes!
Go direct with Flower Window Boxes and get quality products and direct rates. We provide standard and custom PVC window boxes at unbeatable prices and we get them delivered to you faster than anybody else. Our window boxes have been recognized on The Today Show, calling them “the last window boxes you will ever buy!"
We also manufacture custom window boxes and planters in virtually any size. Our PVC planter boxes are made from the same high quality as our window boxes and can be ordered in matching designs.
Click for a fast FREE Estimate on window boxes or call us at 888-505-7715 today!
- Available in Standard size or an Extra Large (XL) size
Standard Dimensions: 8” High x 9-5/8” Wide x 38" Long
XL Dimensions: 10" High x 10-7/8 Wide x 38" Long
Trim adds 3.25" to the total length at top (and 1.5" at bottom if optional base trim is added)
SHIPS FULLY ASSEMBLED
Installing our Window Boxes on Siding (Below):
Installing our Window Boxes on Brick (Below):
DIRECTIONS FOR INSTALLING WINDOW BOXES
* Drill ("hammer action" may be necessary if drilling through brick/rock)
* 5/8" Regular drill bit
* 5/8" Masonry drill bit (brick/rock only) OR 1/4" Regular drill bit (siding/stucco)
* 3/8" Lag bolts (2 for small box, 8 for large box, 3-6 for medium boxes)
* 2" Washers (must fit lag bolts)
* 5/8" Lead anchors (brick/rock only)
WARNING: The following are the manufacturers recommended
installation method. Note that it is recommended that you have a
handyman, carpenter, or other professional install these window boxes to
maximize your safety. The manufacturer of these window boxes claims no
liability or responsibility for damages due to improper installation.
Step 1: Remove your window box from the packaging.
Step 2: Located on the back of your window box various
"penny-sized" marked circles 5/8" in diameter (if no circles are marked
call the manufacturer). Before you drill a hole through the box where it
is marked, you need to ensure that the placement of this hole is
adequate to match your window. If you will be installing on stucco or
siding, it is recommended that your holes drilled overlap a stud (you
will likely modify the placement of the manufacturers pre-marked holes
by moving them left or right a few inches). Because this can vary
depending on the size of your window and how it was installed, please
consult with a local professional to determine the best placement. If
you will be installing on rock or brick, feel free to use the holes that
were pre-marked by the manufacturer, as you are not required to mount
to a stud.
Step 3: Drill a 5/8" hole in the proper locations on the back of your box.
Step 4: Hold the window box up to the window in the desired
location and with a pencil, trace through the drilled holes in the back
of the box so that you are transferring onto the walls of your house the
corresponding location of the holes on the box.
Step 5 - (Brick): Set the window box down. You will now need to
drill where you have marked. If are installing on siding or stucco,
please proceed to Step5 (Siding) Below. If you are installing on brick
or rock, then hammer drill with a 5/8" hammering bit over the marked
spots roughly 3-4 inches deep. Fill the hole with a silicone caulking.
Place a 5/8" expandable lead anchor shield into the hole. Make sure this
lag anchor is sized to receive a 3/8" lag bolt (there are many sizes).
Step 5 - (Siding): If you are installing on stucco or siding, you will need to
pre-drill a 1/4" hole where marked on the house. It is imperative that
this hole be located over a stud to ensure maximum strength. Fill the
hole with a silicone caulking. Proceed to Step 6 below and ignore the
use of anchors related to Brick installation in Step 5 (Brick).
Step 6: Hold the window box back up to the window. The holes in
the back of the box should overlap the anchors in the house. You are now
ready to tighten the lag bolts with a large washer over the lag bolt
and on the inside of the box (make sure the washer is between the head
of the lag bolt and the inside of the back of the box before
Step 7: Prior to fully tightening the lag bolts, you may wish to
place a level in the box to check for levelness. With the lag bolts
tightened 90%, adjust one end of the box till level then finish
tightening the lag bolts securely. This will maximize proper drainage
for your window box.
Step 8: Caulk around your window box to seal it up and keep
water from getting behind it. Caulk over the screw heads as well. This
makes them water tight and prevents water and dirt from getting behind
BRACKET INSTALLATION INSTRUCTIONS
*PVC glue/cement (optional)
*1-1/4" or 1-1/2" screws (2 per bracket - optional)
Please note that brackets underneath are faux brackets that do
not support the box but are for decoration only. You can glue or screw
faux brackets to box at any time and usually after installation so that
they sit flush to the house. GLUE: Apply PVC glue/cement to top of
bracket. Hold to box for 2 minutes. Finish with caulk around the joint
where the bracket meets the box. Although optional, this will give it a
more professional look. SCREWS: Drill two 1-1/3 - 1-1/2 screws into base of
window box and into top of bracket to grab it. Finish with caulk.
Placement of brackets is at discretion of customer. CAUTION: Do Not
install window box brackets directly beneath a drain hole as this may
prevent drainage or cause water to get inside of the brackets and
*Exterior latex paint (color of your choice)
*Paint brush or paint roller
Tips for Prep-work
1.Avoid painting in direct sunlight on a surface that is too warm or heat blistering can occur.
2.Remove any water and dirt on the box first. Moisture trapped under
the paint can push its way out and cause moisture blistering/bubbling.
3.Do not use oil based paint. Make sure that your paint is a 100% acrylic latex paint.
4.Latex can take 2-3 days to dry. For this reason avoid exposing box
to dew, high humidity, moisture, or rain shortly after you have painted
the box. Painting in a damp basement or similar area can lead to
blistering or bubbling of the paint due to water being trapped inside or
under the paint prior to it drying.
It is easiest to paint your window box before installing to your
home. There is no need to prime, sand, or prep your window box. Paint
directly on window box with a brush or roller using any exterior grade
latex paint. There is no need to paint the back of the box. DO NOT PAINT
INSIDE OF BOX, YOU WILL PLANT DIRECTLY INSIDE. If you prefer, you can
paint an inch down to where the
dirt line is. Oil based paints will not work. It's ok to use a
professional spray system and spray the latex paint on or you can simply
brush or roll the box. Let paint completely dry before installing to
your home .
*Optional - Self-Watering Reservoir
*Optional - Rocks, pebbles or Styrofoam peanuts (lighter material)
* Optional - Landscape fabric
*Optional - Soil Moist, or other water absorbing material
* Potting soil
Step 1: Install the window box in desired location.
Step 2: Use either method below or both.
Black Landscape Method
Step 2a: Place a layer of landscape fabric. This will act
as a filter to capture soil prior to water exiting from drain holes.
(proceed to step 3)
Pea Gravel Method
Step 2b: Place a layer of rocks or pebbles. This will act
as a filter to capture soil prior to water exiting from drain holes.
(proceed to step 3)
Step 3: Place your Flower Window Box Self-Watering Reservoir inside of window box.
Step 4: Add nutrient rich potting soil to your window box. Fill up to and within 1 inch from the top of your window box.
Step 5: Proceed by adding your choice of flowers, plants, herbs or seeds.